CCNP Training 

Image-based Installations of NLB Clusters

Image-based Installations of NLB Clusters

Image-based installations, also known as disk cloning or simply cloning, is the fastest method of deploying Windows Server 2003, Enterprise Server. Image-based installations are useful if you are deploying computers that have similar hardware and you want to perform quick, clean installations with minimal end user interaction

Cloning NLB Clusters consists of the following steps:

1. Building a master installation on a master computer. Building a master installation includes installing and configuring the operating system and any software and drivers you need to include on your virtual hard disk.
2. Preparing the master installation with the Sysprep tool. This includes configuring and running the Sysprep tool on the master computer.
3. Generating a virtual hard disk of the master installation with the disk-imaging tool. This includes saving each virtual hard disk to a permanent storage location.
4. Loading virtual hard disks on destination computers that will make up a cluster.

Using SYSPREP to prepare for imaging

 

Building a Master Installation

You need to setup a master computer which you will use to build a master installation and later to create a virtual hard disk.

Building a master installation includes installing and configuring the operating system and any software and drivers you need to include on your virtual hard disk.

Prepare the master installation.

After you have prepared a master installation on the master computer, you need to prepare a virtual hard disk for cloning. Microsoft provides a tool called sysprep that allows you to prepare an image for cloning. The tool can be found on the Windows Advanced Server 2003 CD in the \support\tools directory. When you run sysprep on the master computer, you can supply one of the following two switches: -factory or reseal.

You can use Factory mode to install additional drivers and applications at the stage after the reboot that follows Sysprep. Normally, running Sysprep as the last step in the pre-installation process prepares the computer for delivery. When rebooted, the computer starts Mini-Setup. By running Sysprep with the -factory option, the computer reboots in a network-enabled state without starting Mini-Setup. In this state, Factory.exe processes its answer file, Winbom.ini, and performs the following actions:

1. Copies drivers from a network source to the computer
2. Starts Plug and Play enumeration
3. Stages, installs, and uninstalls applications on the computer from source files located on either the computer or a network source
4. Adds customer data

When finished, run Sysprep with the -reseal option to prepare the virtual hard disk for cloning.

For example, you can create a master installation that contains a minimal set of drivers, run sysprep -factory, create an image of the installation, and copy the image to multiple destination computers. If any destination computers require additional drivers, run sysprep -factory on the destination computer and load those drivers at that time.

For more information about the Factory mode and winbom.ini file, refer to Microsoft Windows XP Preinstallation Guide. This document is located in Deploy.cab on the Windows Server 2003 CD.

If you do not need to install any additional drivers or applications on the destination computers, run sysprep in the Reseal mode.

Sysprep and Sysprep.inf Answer file

To completely automate NLB cluster installation, you will need to use the sysprep.inf file which is an answer file used by sysprep during and after Mini-Setup.

Required Sections and Entries in sysprep.inf

A fully unattended Setup requires the following sections and entries:
Required section Required entries in that section Comments
[Unattended] UnattendMode

TargetPath

  
[GuiUnattended] AdminPassword

TimeZone

  
[Identification] JoinWorkgroup You may instead specify JoinDomain, DomainAdmin, and DomainAdminPassword.
[LicenseFilePrintData] AutoMode

AutoUsers

 Requires AutoUsers ifAutoMode = PerServer.
[Networking]   Required to configure network protocols.
[UserData] ComputerName

FullName

  

Please refer to the Operating System Sections and Entries for Unattended Install section of this document for an explanation of what each of these entries is used for.

NLB-specific Sections and Entries

See section NLB-specific Sections and Entries for NLB specific configuration options in the sysprep.inf answer file.

 

Payless MCSE Boot camp offers Payless MCSE boot camp, MCSE training boot camp, MCSE certification boot camp, MCSE Cisco Boot camp, MCSE Certification training boot camp. MCSE Training certification boot camp, MCSE Boot Training Camp, MCSE boot certification camp, MCSE UK Boot camp, MCSE san Mateo Boot camp, MCSE Japan boot camp, MCSE USA Boot camp, MCSE Europe Boot camp, MCSE guaranteed boot camp.

  • Do you want to become  Real MCSE, CCNA or CCNP certified?
     
  • Do you want to Payless for certification?
     
  • Do you want to finish in 2/3 weeks?

 

 

 

 

MCSE Bootcamp Training - Cheapest, Fast, Guaranteed MCSE certification

 

MCSE Guide

Free MCSE
Free MCSE Training
MCSE
MCSE 2003
MCSE Books
MCSE Boot Camp
MCSE Brain dumps
MCSE Certification
MCSE Exam
MCSE Free
MCSE Jobs
MCSE Logo
MCSE Online
MCSE Online Training
MCSE Practice
MCSE Practice Exams
MCSE Practice Tests
MCSE Requirements
MCSE Resume
MCSE Salary
MCSE Self Paced Training Kit
MCSE Study
MCSE Study Guide
MCSE Study Guides
MCSE Test
MCSE Testing
MCSE Training
MCSE Training Kit
MCSE Training Video
MCSE Windows 2003
Microsoft MCSE Training
Training MCSE
Windows 2003 MCSE

 

 

MCSE : Security Specialist

GET CERTIFIED IN JUST 18 DAYS - 2003 PATH

A router is a device that acts like a bridge or switch but provides more functionality. In moving data between different network segments, routers examine a packet header to determine the best path for the packet to travel. A router knows the path to all of the segments on the network by accessing information stored in the routing table. Routers enable all users in a network to share a single connection to the Internet or a WAN.

 

Use a router to:

 

  • Send packets directly to a destination computer on another networks or segment.

 

Routers use a more complete packet address than do bridges, for example, to determine which router or client should next receive each packet. Routers ensure that packets travel the most efficient paths to their destinations. If a link between two routers fails, the sending router can determine an alternate route to keep traffic moving.

 

  • Reduce stress on the network.

 

Routers read addressed network packets only and pass information only if the network address is known. Therefore, they do not pass corrupted data. This ability to control the data passing through the router reduces the amount of traffic between networks and enables routers to use these links more efficiently than bridges can.


 

 


© Vibrant Worldwide Inc.